Learn About Aquarium Water Pumps

Image for aquarium water pumps
picture of aquarium water pump

Water pumps circulate the water in your tank, directing it through a filter of some type and back into the aquarium proper.

There are several types of water pumps depending on what type of filter you are using and what type of inhabitants the tank will house. Some circulate wholly inside the tank. Others sit outside the tank and pull water from an adjacent sump (water holding tank), through a filter, and back into the tank.

Others simply create currents and waves in the tank.

    Powerheads

Undergravel filter plates usually come with an air pump and air stone that helps water pass through the gravel and back to the tank. However, under gravel filters can also use water pumps (powerheads) to circulate the water. Powerheads sit inside the tank, under the water and attach to the plastic tubes that rise from under gravel filter plates (where the air stone is usually attached) and either pull or push the water through the tubes, causing water to be drawn down through the gravel and plates for filtering.

Manufactures of powerheads rate their "pumps" based on gallons per hour (GPH). A rating of 120 GPH means that the pump will move 120 gallons of water in an hour. Should you choose a powerhead instead of an air pump and air stone to "circulate" the water, you will be required to have some additional information to make the correct choice for your system.

Powerheads are frequently more efficient at moving water through the filter and at alleviating "dead spots" in your aquarium.

Generally speaking, powerheads are somewhat more expensive than air pumps. However, powerheads can help to create more current movement in the tank, bringing water from different levels of the tank and helping to prevent "dead spots" that are hard to circulate, making them more advantageous than most air-stone-driven filtration. There are some new, very sophisticated powerheads that oscillate -turning to and fro - preventing "dead zones" or blowing across corals to produce water movement and stimulation.

Additionally, air pumps are devices used outside the aquarium, and can add to environmental noise, while powerheads are used inside the aquarium (submersible), quietly. Powerheads do warm up the water a little. If either noise or a small amount of heat is a consideration in your system, such consideration might factor into your decision.

A healthy aquarium environment requires the water to be completely circulated at least five to six (5-6) times an hour

To determine the correct powerhead for your system, consider the amount of circulation you will need. Most experts conclude that a healthy environment requires the water to be completely circulated at least five to six (5-6) times an hour. Therefore if your aquarium is 20 gallons, you should choose a powerhead that will pump 20 gallons times 5 (20x5) or at least 100-120 GPH. Choosing a powerhead that moves as much as 10 times the actual water volume of your aquarium is certainly acceptable.

Freshwater aquariums should be relatively placid, without strong currents, but marine aquariums do well with high-flow water pumps providing strong water agitation.

Aeration is important to both fresh and marine tanks. Most aeration takes place at the surface of the aquarium and can be provided either by the flow from the rising bubbles of an air stone or the agitation from a powerhead. Freshwater aquariums should be relatively placid, without strong currents because most tropical fishes come from calm waters.

However, marine coral reef fishes and invertebrates come mostly from strongly moving water with vigorous natural aeration. They prefer aquariums with high-flow water pumps providing strong water agitation in order to have sufficient oxygen. There are newer wave-making systems that incorporate small pumps positioned around the aquarium that can be programmed to produce variable directional water flow to simulate wave or tidal cycles that stimulate reef inhabitants. They are not directly related to the filtering process, but are extremely beneficial to reef tanks. To choose the size of those pumps is fairly arbitrary and determined by the strength of the currents you want to create.

The size and type of pumps as well as the type and material of the air stone are important considerations. (See more information about air stone types)

Use of a powerhead eliminates the need for an air pump in most circumstances.

Should you decide to use a powerhead, you might then ask, "Do I still need an air pump?" The answer could be, "yes" if you still want to use decorations or toys or air stones that require the movement of air to work, then an air pump is still necessary. If the use is limited solely to filtration, use of a powerhead eliminates the need for an air pump.

So what if you're not using an undergravel filter plate in your system but some other type of filter?

    Submersible Pumps
In-line pumps are sealed and can be submersed in water. They usually sit inside the canister filter or the sump of the wet-dry filter.

If you choose a more sophisticated filter like a canister, power, or wet/dry system or you need a pump for your pond, you may be looking for water pumps to power these filter systems. You will be asked to choose between an external pump or an in-line pump.

External pumps are not sealed and must be used in a dry environment, while "in-line" pumps can be submersed in water and are usually housed in the canister or sump of the filter and in the depths of the pond. Internal pumps make less noise, but create more heat.

External pumps are usually used with pond filters. Many pond filters sit inside the pond and have an external pump that brings water from the pond, through the filter and pushes it back into the pond. Rule of thumb is to use the mathematical formula for GPH and take into account any need to push water uphill (head pressure).

The accompanying literature of most good pumps will give you the flow rate reduction for varying feet of head pressure. For example, a Danner pump that has a 500 gallon/per/hour capacity is reduced to 300 GPH when required to push the water up for a distance of 4 feet (the usual approximate distance from your canister or sump to the tank).

Head pressure is the distance from the pump (below) to the tank (above). The higher the tank, the more head pressure there will be to reduce the GPH that the pump can offer.

The most common pumps for canister and wet-dry filters are submersible, in-line pumps. Canister and power filters usually contain their own pumps, already rated by the manufacturer to work efficiently in the configuration they recommend. Choose a canister rated for the number of gallons the manufacturer recommends. They have already taken into consideration whether the canister will sit under the tank or hang on the tank etc. The same is true of power filters.

In the case of a wet/dry filter, look at the pump's GPH rating. Use our formula of 5-6 times turn-over per hour and account for the distance from the bottom of the sump to the top of the tank (if that is where your return water will re-enter the aquarium). Factor in the "head pressure", then choose the size pump that gives you the needed GPH at that height. Most good pumps will give you a factoring diagram for "head pressure" and GPH ratings. Use their recommendation to choose the GPH you need at the head height you require to decide how large a pump to purchase. (It is obviously critical to determine where your pump will be positioned relative to the location of the intake flow tube at the aquarium and the distance between the two before you can purchase a pump for these situations.)

An oversized pump can compensate for pressure lost in head height or turns in the plumbing. It can be adjusted down with ball valves. A pump that is too small cannot be enhanced. Therefore, if at all uncertain, choose the larger rather than the smaller pump.

The last detail is to be certain that your pump of choice has fittings or can be adapted to accept the size tubing or hose you have purchased to connect your pump to the rest of the system. This is a relatively simple thing, but nothing is more maddening than getting your new equipment home ready to set things up and start them running, only to determine there are missing parts to the puzzle.

Vinyl tubing is measured by its inside diameter (I.D.) Look for any unusual tubing requirements. Most water pumps come with adaptors to accommodate several sizes of tubing or they will tell you exactly what size you will need.